Skip to the tool
Speaker Cleaner

Speaker Cleaner

Pick the device you want to clean, check where the sound will play, then press Start. Only the grille position and the sound output change between devices.

165Hz

Ready

60seconds left

165 Hz pulse that pushes droplets out of the grille. 60 seconds.

Set volume to maximum, turn off silent mode, and hold the phone with the speaker facing down.

Disconnect Bluetooth headphones first, otherwise the sound plays there instead of the phone speaker.

Check the result

Play each side. A clean speaker sounds clear and equally loud on both channels.

One tone, many kinds of speaker

Every speaker, from a phone to a Bluetooth speaker, is a thin cone that moves air. A tone at a low pitch makes the cone move more than usual, and that movement pushes water and loose dust back out through the grille. The tone is the same everywhere. What changes is where the grille is, how the sound reaches the speaker, and how you hold the device.

This page opens in Water mode, which suits a speaker that got wet. Use Dust mode for one that just sounds dull. The tool plays through whatever audio output is active, so your first job is always to check where the sound will come out.

Phones, tablets and laptops

These three play the tone from their own built-in speakers. Disconnect any Bluetooth headphones or speaker first, or the sound goes there and the device stays silent.

  • Phone: the main speaker is a row of small holes on the bottom edge, often beside the charging port. Hold that edge facing down and use Water or Dust mode.
  • Tablet: the speakers sit at the bottom or along the short sides. A tablet moves more air than a phone, so try Manual mode with a sine wave at 100 to 140 Hz.
  • Laptop: the grilles can be beside the keyboard, under the front edge or on the base. Tilt it so the grille side faces down, and use Manual mode at 100 to 140 Hz.
  • For all three, set the volume to maximum for the run and keep the device still. A laptop is best held over a towel so nothing rattles on the desk.

Earbuds, headphones and Bluetooth speakers

Here the sound has to go to the device you want to clean, so connect it first. Pair the earbuds or speaker, check that the volume buttons control it, then start the tone. It will play through them.

  • Earbuds and headphones: take them out of your ears before you press Start. Use the gentle Ear speaker mode, not Water or Dust. Earwax does not move with sound, so brush the mesh with a soft dry toothbrush.
  • Bluetooth speakers: many outdoor models are rated water resistant, so check the rating before you treat one as wet. Point the grille down and run Water mode, or play a song with strong bass. Dry it fully before you charge it.

Smartwatches need their own tool

Apple Watch has its own Water Lock, which clears water out of the watch speaker when you turn it off. For that speaker it is the better tool, so use it instead of this page.

A web page cannot play sound through the speaker of most smartwatches, so do not expect this tool to clean one. If the watch speaker stays muffled after its own feature, check the maker's advice or ask a repair shop.

A routine that fits any device

  1. Wipe the outside dry with a soft cloth and take off any case or cover.
  2. Choose the output. Disconnect Bluetooth to clean the device itself, or connect the earbuds or speaker you want to clean.
  3. Turn the volume to maximum and switch off silent mode. If you are cleaning earbuds, take them out of your ears first.
  4. Point the grille down and hold the device still.
  5. Press Start in Water mode for a wet speaker, or Dust mode for a dull one, and let the full 60 seconds play.
  6. Wipe the grille, then play a song or a voice note to hear the result. Run it once more if the sound is still muffled.

Cleaning sound for AirPods

Questions people ask

Does one cleaner really work on a laptop and a Bluetooth speaker?

The tone itself works on any small speaker that can play it. Laptops and tablets move more air than phones, so low settings around 100 to 140 Hz suit them. Results still depend on the cause. Sound moves water and loose dust, not stuck grime.

Can I clean a laptop speaker without opening the laptop?

Yes, for water or loose dust in the grille. Play the tone through the laptop itself with headphones unplugged, tilt the grille side down and brush the holes lightly. Never open the case yourself; dust inside needs a repair shop.

Why does the tone play from my earbuds and not my phone?

Because the earbuds are still connected. The tool plays through whatever output is active. Disconnect Bluetooth to clean the phone, or keep them connected, out of your ears, to clean the earbuds.

Can I clean my smartwatch speaker with this page?

Almost certainly not. Most smartwatch speakers cannot be reached by a web page. Apple Watch owners should use Water Lock. Other watches may have a similar feature in their settings.

Is it safe to run this on a water resistant Bluetooth speaker?

Yes, in the sense that it is only playing sound. Check the speaker's rating, keep the volume sensible for its size, and dry it before charging. A speaker with no water rating should be dried first, and not run if liquid may be inside.

More cleaning tools